Garage Floor Epoxy in Cedar Rapids, Iowa

Cedar Rapids has long, cold winters with plenty of snow, and a garage floor takes all of it. This page covers what epoxy costs, how the job goes and what to ask before you book. Send the short form for a quote.

Three national price guides put a garage floor epoxy job at about $1,500 to $3,800, averaging about $2,250.

Source: InchCalculator, Bob Vila and Thumbtack, retrieved 2026-11-18. The figures are averaged across the three.

Request a quote

Close-up of a glossy gray epoxy garage floor with a speckled flake finish and soft reflections
  • $2,250

    Average of three published guides for a garage floor epoxy job

  • $4 to $10

    Per square foot, installed, on average

  • 26.7 in.

    Average yearly snowfall in Cedar Rapids

Sources: InchCalculator, Bob Vila, Thumbtack, HomeGuide and Wikipedia (NOAA climate data), retrieved 2026-11-18.

Garage floors in a Cedar Rapids winter

Cedar Rapids is a city in Linn County, Iowa, with an estimated 137,935 residents in 2025. Winters are long and cold, with plenty of snow.

The lowest temperature on record is -30 °F, set on January 31, 2019. That is the weather a garage floor lives with, so ask how the floor will be prepared and checked for moisture.

The cost figures below are national guides, because none of them states a Cedar Rapids price.

What a garage floor coating can include

Ask a contractor to quote the prep, the coating and the topcoat separately, so you can compare like with like.

  • A person rolling gray epoxy onto bare concrete in a garage, with the finished speckled floor on the left

    Epoxy coating for a bare garage floor

    An epoxy coating goes on over prepared concrete. Prep can mean grinding off about 1/32 inch of the surface to remove sealers or hardening agents.

    Ask about this floor
  • Two workers prepping a cracked concrete floor with a grinder and vacuum, with a moisture meter beside a taped plastic sheet

    Prep for sealed, stained or cracked floors

    Prep comes first. When epoxy peels up early, the cause is most likely too much moisture in the slab, so ask how the slab will be checked.

    Ask about this floor
  • Newly coated gray flake epoxy garage floor with caution tape and a pedestrian sign marking off the surface

    Topcoats and finishes

    A coating can be ready for foot traffic before it can take a car. Ask which system the contractor uses, and ask for that product's cure schedule.

    Ask about this floor

What does garage floor epoxy cost in Cedar Rapids?

Published guides give a range, and none of them states a Cedar Rapids price. These figures are combined from three guides.

Typical garage floor epoxy prices, combined from three published guides
Point in the rangeTypical price
Low end$1,500
AverageAbout $2,250
High end$3,800

Averaged across InchCalculator, Bob Vila and Thumbtack. Bob Vila's page was last updated in April 2024. HomeGuide gives $1,600 to $5,800 for a 2-car garage. One Cedar Rapids installer lists $7.50 per square foot with a $1,800 minimum. These are published figures, not a quote. Source: InchCalculator, Bob Vila, Thumbtack, HomeGuide and the installer's own page, retrieved 2026-11-18.

Get a price for your garage floor

Send the short form below.

How a garage floor coating job goes

  1. Send the form

    Describe the floor in the short form: bare, stained, cracked or already coated.

  2. Floor check

    A local contractor may contact you, look at the floor and give a price.

  3. Prep

    The surface is prepared first. That can mean grinding off about 1/32 inch of concrete to remove sealers or hardening agents.

  4. Moisture

    Too much moisture in the slab is the most likely cause of early peeling, so ask how it will be checked. Family Handyman says the common plastic-sheet test, taping plastic to the floor and looking for condensation after 24 hours, is not reliable.

  5. Coat and cure

    The coating goes on, then cures. Foot traffic comes before vehicle traffic, and the product's own schedule sets the times.

  6. Ready to start?

    Send the short form for a price on your floor.

    Request a quote

Cedar Rapids and nearby

Cedar Rapids is in Linn County, Iowa. Marion is also in Linn County, and Hiawatha is a suburb on the northwest side of Cedar Rapids.

  • Cedar Rapids
  • Marion
  • Hiawatha

Questions about garage floor epoxy

What is the average cost to have a garage floor epoxy coated?

Three published guides average about $2,250, with a typical range of about $1,500 to $3,800: InchCalculator says $2,000, Bob Vila $2,441 and Thumbtack about $2,370. HomeGuide puts epoxy at $4 to $10 per square foot installed on average, with materials at $1 to $5 and labor at $3 to $5. None of these is a Cedar Rapids quote.

How much would it cost to epoxy a 20x20 garage floor?

A 20 by 20 foot garage is 400 square feet. At HomeGuide's $4 to $10 per square foot, that is $1,600 to $4,000. HomeGuide puts a 2-car garage at $1,600 to $5,800.

What are the downsides of using epoxy on a garage floor?

It needs prep: grinding off about 1/32 inch of concrete to remove sealers or hardening agents is one step. Too much moisture in the slab is the most likely cause when epoxy peels up early. A floor that takes foot traffic may not yet take a car, so the cure schedule matters.

How much does 1,000 sq ft of epoxy cost?

At $4 to $10 per square foot installed on average, 1,000 square feet comes to $4,000 to $10,000. A garage is far smaller than that: HomeGuide puts a 2-car garage at $1,600 to $5,800.

Does road salt hurt a garage floor?

Cedar Rapids keeps about 9,000 tons of salt and sand and 10,000 gallons of brine on hand for winter. An Iowa State University study found calcium chloride did the most damage to portland cement concrete of all the deicing chemicals tested, especially in freeze and thaw conditions. That research is about pavement, not garage floors, so ask a contractor how a coating protects the slab.

How long before I can drive on a new floor?

It depends on the product. A coating can be ready for foot traffic before it can take a vehicle, so ask the contractor for the cure schedule of the exact product being installed.

Can I epoxy a garage floor myself?

Family Handyman says to follow the surface preparation instructions to the letter, which means grinding off about 1/32 inch of concrete to remove surface sealers or hardening agents. It also says too much slab moisture is the most likely cause when epoxy peels early, and that the common plastic-sheet test is not reliable. Check the product's data sheet for its moisture limit before you buy.

Get your garage floor priced

Send the short form and say what the floor looks like today.

Glossy dark flake epoxy garage floor with shelving on the left and an SUV parked by the glass garage door
Get a quote